Primers, undercoats, metal plating and top coats: everything that goes on before and after your colour.

Which one do I need?

Quick picker

Spray everything in this range from at least 20 cm, apart from Top Wax, which goes on with a cloth.

Primers

Use a primer on any bare (unpainted) metal or carbon before you paint. Painted frames don't need one.

Frame Builder's Metal Primer

Metal Primer

A modern anti-corrosive primer for any bare metal frame.

Colour: whiteDistance: 20 cm+Coats: 1Drying: 20 minutes
  • White acrylic anti-corrosive primer
  • For aluminium, steel, stainless steel and titanium
  • Gives Spray.Bike paint a strong grip
  • No heat treatment needed
  • On steel, a modern alternative to Cold-Zinc

How to use it

It's an all-purpose acrylic primer with ingredients that stop corrosion, so it prevents rust. Being acrylic, it's straightforward to use. It is quite wet, though, so don't get too close or it will dribble: spray from at least 20 cm.

It's sandable when dry, so mistakes rub away. And because it's white, you can see where you've been, which makes it easier than Cold-Zinc on steel. Grey primer on grey metal is hard to follow!

Outside only

This primer is only for the outside of the tubes. It's thick, so keep it out of the inside of your frame, or you'll never get that seat post back in.

Shop Metal Primer →

Frame Builder's Cold-Zinc

Cold-Zinc

The traditional way to protect bare steel from rust.

Colour: metallic greyDistance: 20 cm+Coats: 1Drying: 30–60 minutes
  • 95% galvanised zinc primer
  • For raw steel tubing, inside and out
  • On steel, the historically accurate alternative to Metal Primer

How to use it

Steel frames used to be zinc-dipped before painting, to stop rust and make the frame last longer. Cold-Zinc follows that tradition. It's 95% galvanised zinc dust and just 5% binder, so it works as both a primer and an anti-rust coat.

Because you're spraying almost pure metal, it takes a little practice. The zinc is a powder carried in liquid that evaporates as it leaves the can. Too far away and it won't stick well. Too close and you'll get wet zinc running everywhere. Keep to at least 20 cm, and try it first on something solid and curved, metal or plastic, to get the feel of it. Don't overdo it: one coat is perfect.

A quick squirt inside the seat tube is a good idea. Keep the can upright, so hold the frame up to do it.

We say raw steel only, but we've also had good results using it as a primer on chrome and nickel plating.

Wear a mask

This is metal in dust form, and you mustn't breathe it in. If that feels like a lot, Metal Primer is easier and safer to use, almost like our paint. Just remember it's for the outside of the tubes only.

Shop Cold-Zinc →

Frame Builder's Carbon Primer

Carbon Primer

A clear primer for raw carbon fibre and resin composite frames.

Colour: clearDistance: 20 cm+Coats: 1Drying: 10–15 minutes
  • Made for raw carbon fibre and composites
  • Gives Spray.Bike paint a strong grip
  • No heat treatment needed

How to use it

Raw carbon, woven or composite, is famously hard to paint. Carbon Primer is an etch primer. It dries with a rough texture so thin you can't see or feel it, but it gives the paint something to hold on to.

It's a bit odd at first. It seems to run like water, then it lies flat and settles. Try it on something solid and curved, metal or plastic, before you go near your expensive carbon friend. Spray from at least 20 cm and don't overdo it: one coat is perfect. If any dribbles show once it's dry, sand them away lightly.

Because it's clear, you can prime the whole bike and still leave some carbon showing where you don't paint.

Shop Carbon Primer →

Undercoat

Frame Builder's Smoothing Putty

Smoothing Putty

A thick cover-all putty for tatty frames.

Colour: greyDistance: 20 cm+Coats: 1 or more
  • Covers scratches, rust damage and stickers
  • For steel, aluminium and even carbon parts
  • Sands down easily
  • No heat treatment needed

How to use it

Hold the can at least 20 cm away. Once it's dry, sand it smooth, then paint.

If you're also using Cold-Zinc or Metal Primer, prime first and put the putty on afterwards.

Shop Smoothing Putty →

Metal Plating

Frame Builder's Metal Plating, Copper

Metal Plating

Copper, Bronze Gold, Brass Gold and Pewter Silver, with a high metal content.

Distance: 20 cm+Cover: one can does a frame and forkFinish: slight satin

How to use it

You can spray Metal Plating straight onto existing paintwork. On a bare surface, use the right primer first.

Note the distance: at least 20 cm, further than the other colours. It dries hard with a slight satin finish and won't rub off. For protection against the weather, you can add Transparent Finish on top.

Wear a mask

The Metal Plating colours have a high metal content, so always wear a mouth and nose mask.

Shop Metal Plating →

Top coats

Spray.Bike colours are matte. Add a Transparent Finish for a satin or gloss shine, or to protect them and keep them matte.

Frame Builder's Transparent Finish – Satin/Gloss

Transparent Finish – Satin/Gloss

An acrylic clear coat that adds a satin or gloss finish.

Colour: clearDistance: 20 cm+Coats: 1 for satin, 2+ for glossBetween coats: 2 hoursFull cure: 24 hours+
  • For steel, aluminium and carbon parts
  • No heat treatment needed

How to use it

Make sure the paint underneath is completely dry. Shake the can well, hold it at least 20 cm away and waft gently, keeping your hand moving all the time. One coat is the minimum. Leave 2 hours between coats and at least 24 hours for a full cure.

Shop Transparent Finish – Satin/Gloss →

Frame Builder's Transparent Finish – Matte

Transparent Finish – Matte

An acrylic clear coat that keeps things matte.

Colour: clearDistance: 20 cm+Coats: 1 or moreBetween coats: 2 hoursFull cure: 24 hours+
  • On top of Spray.Bike colours, to protect them and keep them matte
  • Also turns any existing gloss finish matte
  • Looks glossy when it first goes on, but quickly dries matte

How to use it

Exactly as for Satin/Gloss: completely dry paint underneath, at least 20 cm away, hand always moving. Don't worry when it looks glossy at first, as it dries matte.

Shop Transparent Finish – Matte →

Stickers and decals

Put new stickers or decals on top of your new paint, then seal them with Transparent Finish.

Very occasionally, the acetone in Transparent Finish can make the ink on a decal run. Test it on a spare one first. If the ink runs, put your decals on top of the Transparent Finish instead.

Matte Transparent Finish leaves a frosted layer on clear surfaces, so don't spray it over stickers with a clear backing, unless you want them frosted.

Care

Frame Builder's Top Wax

Top Wax

A water-based finishing wax for every bike.

Colour: clearApply: with a cloth, not sprayed on the frame
  • Leaves an invisible, very thin protective layer on painted metal, carbon, even wooden frames
  • Doesn't add shine to matte paint, so it's perfect for Spray.Bike colours
  • Contains carnauba wax

How to use it

Don't spray it straight onto the frame. Spray it onto kitchen paper or a lint-free cloth and rub it on gently. Do it again regularly, especially after you clean your bike.

Shop Top Wax →

Back to the How to use guide