Everything you need to know about painting your bike with Spray.Bike. Can't find your answer? Get in touch and we'll help.
Before you start
Is one can enough for a whole bike?
Yes. One 400ml can covers a typical frame and fork in a single coat, as long as you keep to the right spray distance. For our Fluro colours, we recommend a light base coat of white first (Metal Primer, Marylebone or Whitechapel), so you may want a second can for that.
Do I need to take the bike apart?
Yes. Strip off all the components and mask anywhere parts will be refitted, such as the headset cups, bottom bracket shell and seat tube.
How should I hang the frame?
Hang it so you never have to put it down while painting, for example from a bike stand or a rope through the head tube. Make sure you can reach every part of it.
Do I need to strip the old paint?
No. Sand the factory paint with 400–800 grit paper instead, and it acts as a primer. Avoid chemical strippers, as they leave a residue that stops the paint sticking. Sandblasting is fine, but then prime the bare metal first.
How do I prepare a metal frame?
Sand painted metal with 400–800 grit. If you're down to bare metal, wet sand with around 220 grit, then 400 grit. Clean the whole frame with rubbing alcohol before painting. Never use acetone or alcohol on top of Spray.Bike paint.
How do I prepare a carbon frame?
Wet sand painted carbon with 600 grit and clean it with rubbing alcohol. A light coat of Carbon Primer helps the paint grip.
Do I need a primer?
Spray.Bike goes straight onto pre-painted frames. For anything bare, prime first:
Bare aluminium or steel: Metal Primer, or Cold-Zinc for steel
Bare carbon or composite: Carbon Primer
A mix of bare metal and factory paint: prime the whole frame
What about rusty steel?
Sand the rust away, starting with steel wool and working down to around 300 grit. Clean with alcohol, apply Cold-Zinc, then use Smoothing Putty to fill and level any rough patches.
Can I use it on a mountain bike?
Yes, but expect some scratches. Chain slap is hard on any paint, so a chainstay protector is a good idea.
Spraying
How far away should I spray?
Colours: 4–10 cm
Primers, Cold-Zinc, Smoothing Putty, Transparent Finish and Metal Plating: at least 20 cm
Top Wax: spray onto a paper towel or lint-free cloth and wipe it on gently
How long should I shake the can?
Shake well for 3 full minutes, until the ball inside moves freely.
How many coats do I need?
One. Spray, wait about 30 minutes, then check the frame under different lights and touch up any thin spots. Use the least paint you can: extra layers make the finish less durable, not more.
Any tips for Fluro colours?
Spray close, at about 5–10 cm
Paint at 13–18°C, and never above 24°C
Do a test spray first, keep the can upright and turn the frame rather than the can
Put down a light white base coat first
20–30 minutes after painting, rub gently with baking parchment
Finish with a couple of top coats
Afterwards, clear the nozzle by turning the can upside down and spraying until nothing comes out
Should I sand between coats?
You don't need to. If you do, use a fine grade and take care not to blend colours.
My nozzle is clogged. What do I do?
Scrape the dried paint off the outside of the nozzle, refit it, shake the can and press to clear it. You can also swap in a nozzle from another can of the same colour.
What weather is best?
Paint in a well-ventilated space, ideally on a mild, dry day. Avoid heat, cold, rain and humidity. Always wear a respirator: our Essential Safety Pack has everything you need.
Drying and finishing
How long between coats?
Around 2 hours between colour coats, and 24 hours between top coats. Cooler weather, humidity and thicker coats all add to that.
When can I rebuild the bike?
Wait about 7 days for the top coat to cure fully. The longer you leave it, the tougher it gets.
Which top coat should I use?
For a matte finish, use Transparent Finish – Matte. For satin or gloss, use Transparent Finish – Satin/Gloss. Then keep it protected with regular coats of Top Wax.
Can I paint over powder coat?
Usually, yes. Sandblasting is best. If not, sand through the clear top layer, rough the surface up and clean it thoroughly.
Can I paint components, plastic or titanium?
Often, with careful sanding, cleaning and the right primer: Metal Primer for metal parts, Carbon Primer for plastic or fibreglass. Anodised and polished parts are tricky, flexible plastics may crack, and durability can't be guaranteed.
Designs and masking
When can I mask over fresh paint?
After at least 2 hours, but overnight is much safer.
Which masking tape should I use?
A low-tack automotive masking tape, such as our Q1 Premium Masking Tape. For printed designs, ask a sign shop for low-tack or high-bake vinyl. Strong stickers can pull paint off if it hasn't fully cured.
Problems
I've made a mistake. Can I fix it?
Almost always. Lightly sand the area, mask around it and respray. If you're stuck, get in touch.
Can I get back to the original factory paint?
You can sand Spray.Bike off, but the frame won't go back to its original factory finish.
Do you colour match?
No. Every colour we make is on the website.
Orders, delivery and returns
Where do you deliver?
We ship to the UK and much of Europe. Free UK delivery on orders over £75. See Delivery & Returns for the full list of countries and delivery costs.
Can I return something?
Yes. You can return unused items within 14 days of receiving them for a full refund. Between 14 and 30 days, there's a 5% restocking fee unless the item is faulty or was sent in error. After 30 days, we can't accept returns. Faulty or wrong items are replaced or refunded at no cost to you. Please contact us before sending anything back.